⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6251 Threads Posts
to

FS-Bandsaw Blades

I recently bought a quantity of bandsaw blades on ebay, figuring that I could use some of them in my home shop..and all...
14 comments posted 20yrs
posted by gunner
14 comments posted 20yrs posted by gunner

MIG wire speed control problems

Hi all: I am trying to repair the wire speed control on a Century welder Model 83132. The control has a very short usab...
9 comments posted 20yrs
posted by ramray
9 comments posted 20yrs posted by ramray

Tuyere holes

Are 5- 3/16" holes in a tuyere in a farries 16-1/2" forge, with a 100 cfm blower, enough?
0 comments posted 20yrs
posted by footboarder
0 comments posted 20yrs posted by footboarder

propane torch conversion to natural gas?

Brazing, not welding, but .. I have some propane/air torches I want to convert to natural gas (methane). Can I just swap...
2 comments posted 20yrs
posted by zenadsl6186
2 comments posted 20yrs posted by zenadsl6186

weldingfaq website - need new maintainer

Hi everyone The "welding" website... We have to take over the www.weldingfaq.com website if we want it to continue. Lar...
0 comments posted 20yrs
posted by r0d1s3
0 comments posted 20yrs posted by r0d1s3

Speaking of winmiter...

--The thing is my eyes aren't all that great and, although the program makes a dandy template it's *really* hard for me...
8 comments posted 20yrs
posted by steamer
8 comments posted 20yrs posted by steamer

Lincoln "coffee grinder" DC stick welder

A couple of years ago I posted an inquiry about an old Lincoln 3 phase "R2D2" welder I bought on ebay. Specifically, I'...
12 comments posted 20yrs
posted by vtuck
12 comments posted 20yrs posted by vtuck

OT: Help identifying a hydraulic fitting

Hello, I know this is a little off topic, but this NG is a wealth of information and I'm stumped on this one. I'm tryin...
3 comments posted 20yrs
posted by larry
3 comments posted 20yrs posted by larry

I finally got a engine driven welder

Guys, Need a little feedback here.... I picked up a good running Miller AEAD-200 welder for $650.00 It's being delivere...
5 comments posted 20yrs
posted by NT_Geek
5 comments posted 20yrs posted by NT_Geek

Pipefitting Question

I would appreciate any tips on mitering/fitting some pipe. Specifically I am working with 6" thin wall making a 3 piece...
5 comments posted 20yrs
posted by albieguyspamless
5 comments posted 20yrs posted by albieguyspamless

Cracked Block

I am rebuilding my Ford 9N tractor engine after a series of unfortunate events. After replacing the cam and timing gear...
9 comments posted 20yrs
posted by bmcdougald
9 comments posted 20yrs posted by bmcdougald

Pressure/ friction welding of two metals

I am working on some soft metal thin film and wire, i.e. gold wire bonding to gold thin film. We all know that when two...
3 comments posted 20yrs
posted by ngarchun
3 comments posted 20yrs posted by ngarchun

Another Business Question

Greetings all, I attended a siminar today put on by the local Small Business Developement Center (SBDC) concerning SBA...
3 comments posted 20yrs
posted by jimnthemNOSPAM
3 comments posted 20yrs posted by jimnthemNOSPAM

Not exactly porosity, but..

--Sometimes, just at the end of a bead I'm doing in tig, after I shut off the power, the bead ends with this thing shap...
11 comments posted 20yrs
posted by steamer
11 comments posted 20yrs posted by steamer