⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

Rebuild Cost for Two Stage Regulators

I have a vintage pair of two stage regulators, an OXWELD R65 and an AIRCO B40. Can anyone provide any guidance about th...
11 comments posted 22yrs
posted by TheGuy
11 comments posted 22yrs posted by TheGuy

Airco 250 Heliweld V info?

Looking for manual and source for parts. Any suggestions appreciated.
1 comments posted 22yrs
posted by only
1 comments posted 22yrs posted by only

hobart small champion dc welder

It seems that Hobart/Miller is discontinuing their small DC engine driven welder 500390 and replacing it with an AC weld...
0 comments posted 22yrs
posted by <kbgreen
0 comments posted 22yrs posted by <kbgreen

why aren't my SS TIG welds shiny?

greets all, just a quick question.. subject line says it all. i'm not talking about the backside, either.. the top.. i...
8 comments posted 22yrs
posted by tony
8 comments posted 22yrs posted by tony

newbie to the group.

Hi everyone. I'm new and wanted to introduce myself. I'm 23 and in school right now for welding and fab. technology (gr...
9 comments posted 22yrs
posted by muzikmadness2003
9 comments posted 22yrs posted by muzikmadness2003

Weldor banished to the office

Hello everyone Finally found a new job and things were going great installing misc metals and welding, the foreman aske...
5 comments posted 22yrs
posted by johnanoon
5 comments posted 22yrs posted by johnanoon

overhead cranes

over the years i've heard stories of overhead crane motors being ruined when they are hooked to a piece being welded. i...
0 comments posted 22yrs
posted by tittiesandbeer
0 comments posted 22yrs posted by tittiesandbeer

setting mig - weldreality approach?

Hi All, I was reading ed craig's weldreality last night and got to thinking about my own welding practices; specificall...
6 comments posted 22yrs
posted by askshaun
6 comments posted 22yrs posted by askshaun

postings

Have followed this group since 1998. Met many friends along the way. My real concern is the off topic stuff, including...
4 comments posted 22yrs
posted by brad254
4 comments posted 22yrs posted by brad254

FS: Rotary bender, SFBA

--Trying to find a new home for a power rotary bender --Location: San Franciso Bay Area http://www.nmpproducts.com/forsa...
0 comments posted 22yrs
posted by steamer
0 comments posted 22yrs posted by steamer

rose bud

Also keep in mind that a rose bud requires a very large flow of fuel. A single small (approx 125 cubic ft) acetylene cy...
2 comments posted 22yrs
posted by allanhholst
2 comments posted 22yrs posted by allanhholst

Welding Rates

Anyone have a link to a site that has information on the relative speed of each process (MIG, TIG, stick, O/A, etc.)? In...
6 comments posted 22yrs
posted by riflemanjake
6 comments posted 22yrs posted by riflemanjake

O/A Tank Transportation

I'm thinking about getting an O/A welding setup, but only have a small car (Honda Civic). I know filling the larger cyl...
10 comments posted 22yrs
posted by riflemanjake
10 comments posted 22yrs posted by riflemanjake

correct setting for a rose bud tip on torch..

Yesterday I attempted to heat the side of the bucket on my bobcat loader in order to knock some of the dents out of it....
2 comments posted 22yrs
posted by bruce
2 comments posted 22yrs posted by bruce