⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

AO Spary Welding

Does anyone know if you can use a AO spray welding handle to spray plastic's or ceramic coatings? Do you know where to g...
4 comments posted 17yrs
posted by gamorrisHOME
4 comments posted 17yrs posted by gamorrisHOME

Welding the bed of a Truck

I recently picked up a 2007 diesel truck for a decent price, but the previous owner had instaled a thru-bed goosekneck...
12 comments posted 17yrs
posted by nospam
12 comments posted 17yrs posted by nospam

Welding Device ID

I'm trying to identify an object that was photographed in the back of truck that appears to contain welding equipment....
16 comments posted 17yrs
posted by rhvp65
16 comments posted 17yrs posted by rhvp65

Wish Me Luck !

I've decided to go into business for myself (been there before ...) building window bars and A/C surrounds . I've check...
11 comments posted 17yrs
posted by snagone
11 comments posted 17yrs posted by snagone

Clamps

Usually I don't buy extra stuff from MSC but I had to bite in these clamps at the bottom of page 27. http://www1.mscdir...
10 comments posted 17yrs
posted by matthew31
10 comments posted 17yrs posted by matthew31

$429 good price for Lincoln 135T Mig kit?

Local Sears has them on clearance for $429. They'll do 24ga up to 1/4". I'm aware of the limitations of a 120V machine,...
0 comments posted 17yrs
posted by mkirsch1
0 comments posted 17yrs posted by mkirsch1

Stop Home Foreclosure Now

Stop Home Foreclosure Now 100% Guaranteed Free Consultation, No Obligation click here for more http://www.homeassure.com...
0 comments posted 17yrs
posted by katrina.traviesa69
0 comments posted 17yrs posted by katrina.traviesa69

Welding a pulley on to a shaft

My generator head cooked and I would like to use the engine for a new setup however the engine has a tapered shaft and...
7 comments posted 17yrs
posted by bluearc5
7 comments posted 17yrs posted by bluearc5

Banished

My wife has asked me to stop using the gopher blaster. Says it is too hard on the dogs, and I'm becoming accident prone...
5 comments posted 17yrs
posted by toquerville
5 comments posted 17yrs posted by toquerville

Syncrowave gives too much high frequency

I have realized that my Syncrowave 250 gives way too much high frequency. It can start HF arcs from an inch or so. Sett...
7 comments posted 17yrs
posted by ignoramus20688
7 comments posted 17yrs posted by ignoramus20688

Cylinder cart

I ended up getting this cart: Valley Craft® Deluxe Gas Cylinder Double Truck, 50"H x 22"W x 14-1/2"L 1 EA Shown here...
21 comments posted 17yrs
posted by ignoramus22888
21 comments posted 17yrs posted by ignoramus22888

Welding positioner for the working poor

When I weld some things, such as especially pipes, but other things also, I often want to hold then relatively firmly i...
24 comments posted 17yrs
posted by ignoramus22888
24 comments posted 17yrs posted by ignoramus22888

Generator?

I need to electrifry my shop. It will cost $$$ to run a new line from the power pole. So, I want a generator. I need to...
23 comments posted 17yrs
posted by toquerville
23 comments posted 17yrs posted by toquerville

Graffiti with welding rod

I made a few attempts yesterday to write letters with welding rod, just for fun (using that Hobart 650-RVS). I used 1/8...
8 comments posted 17yrs
posted by ignoramus21542
8 comments posted 17yrs posted by ignoramus21542