⋐⋒⋐ Computer Numeric Control

  1. Home
  2. ⋐⋒⋐ Computer Numeric Control
2667 Threads Posts
to

determining kc (specific cutting force).

Could any one tell me formula you use to determine specific cutting force. Current Sandvik catalog doesn't include form...
1 comments posted 18yrs
posted by hacdunqh
1 comments posted 18yrs posted by hacdunqh

Survey: Is Your Cell Phone Your Only Phone?

To All: I've got a couple of friends whose only home phone service is cell phone service. I was wondering how common th...
39 comments posted 18yrs
posted by bottlbob
39 comments posted 18yrs posted by bottlbob

Coolant - No Coolant

To All: I am doing some 2" X 2" X 2" 17-4 PH aerospace parts that are quite involved with about 5 setups (bores, radii,...
6 comments posted 18yrs
posted by bottlbob
6 comments posted 18yrs posted by bottlbob

Shopturn

Hello Do you know where can I download trial or demo version of Sinumerik Shopturn ? I would be very grateful for help :...
0 comments posted 18yrs
posted by miloww
0 comments posted 18yrs posted by miloww

Hass programmer/teacher needed Orange County Cal.

Got a start up company with a Hass mill...and not a friggin clue how to set up , program and run it. Anyone in the Irvin...
5 comments posted 18yrs
posted by gunner
5 comments posted 18yrs posted by gunner

Shop Tunes

I don't know why; but sometimes my brain just does the strangest things. One night, a while ago, I was sitting at my ho...
2 comments posted 18yrs
posted by kg1
2 comments posted 18yrs posted by kg1

G19 different for Fanuc?

I've used G17,18,19 on several controls... They all act exactly like I expect, and all exactly the same.... Until I get...
8 comments posted 18yrs
posted by 3t3d
8 comments posted 18yrs posted by 3t3d

IC Engine Books

I liked this review. The book is no longer in print but can be purchased used: http://www.amazon.com/Engine-repair-asse...
0 comments posted 18yrs
posted by jon_banquer
0 comments posted 18yrs posted by jon_banquer

NEW

I am new to cnc. Can anyone tell me briefly about the servo module and its working? Also about the SRAM in the Fanuc Cnc...
2 comments posted 18yrs
posted by jprabakaran.jp
2 comments posted 18yrs posted by jprabakaran.jp

SW2008 vs Inventor 11

Has anyone used both products; is either one substantially better? TIA
4 comments posted 18yrs
posted by joseph
4 comments posted 18yrs posted by joseph

Oi-MC

i am able to run the m/c with out encoder by setting bits in parameter 4000.0,4001.1,4005.0 from 1 to 0. But eventhough...
2 comments posted 18yrs
posted by jprabakaran.jp
2 comments posted 18yrs posted by jprabakaran.jp

Anyone Tried This?

http://www.use-enco.com/CGI/INSRIT?DCMP=EMC-1406031&PMAKA=317-6192 If so how does it work and do you think it's worth it...
8 comments posted 18yrs
posted by jon_banquer
8 comments posted 18yrs posted by jon_banquer

Gibb V9 Flash CPR

Reported to need 4 gigs or RAM to properly run Flash CPR (MachineWorks). 2 gigs of RAM is very, very slow. Jon Banquer S...
0 comments posted 18yrs
posted by jon_banquer
0 comments posted 18yrs posted by jon_banquer