⏣ General Metalworking

30778 Threads Posts
to

What is flint?

When changing the flint in my torch sparker I began thinking about the flint. I know that flint is a stone but the spar...
6 comments posted 22yrs
posted by micrio_DELETE_THIS_
6 comments posted 22yrs posted by micrio_DELETE_THIS_

Do unused floricient bulbs go bad?

About 5 years ago I installed a bunch of fluorescent light fixtures in my shop. They all used the 4 foot bulbs that are...
25 comments posted 22yrs
posted by micrio_DELETE_THIS_
25 comments posted 22yrs posted by micrio_DELETE_THIS_

OT: Degaussing AlNiCo magnet

I need to degauss some AlNiCo magnets. They are cylindrical (2" OD, 1.5' ID, and 1" long). We charge them with a single...
4 comments posted 22yrs
posted by rileyesi
4 comments posted 22yrs posted by rileyesi

Table and Circ saw blades for metal

Gang, A while back, someone posted a link to a company that sells table and circular saw blades especially for cutting...
7 comments posted 22yrs
posted by cassarole
7 comments posted 22yrs posted by cassarole

Mill table toggle clamp needed

Hi all, I need some toggle clamps that are set up to accept T-nuts and studs in a mill table. I KNOW I've seen these re...
5 comments posted 22yrs
posted by pgrey
5 comments posted 22yrs posted by pgrey

What is the true refill pressure fo acetylene tank?

I ve read everything from 75 to 40 psi. Mine just dropped at about 80 psi and called in for a new one (rented tank). No...
4 comments posted 22yrs
posted by tharkaduso
4 comments posted 22yrs posted by tharkaduso

C-6 lathe spindle mount

Hi I cannot find any dimensional information on a C-6 spindle mount. Is it interchangeable with a D1-6 mount? it looks q...
1 comments posted 22yrs
posted by sbaer
1 comments posted 22yrs posted by sbaer

Metal house numbers needed

I need eight flat plate metal numbers to mount on rods, and then mount to a boulder in my front yards. 3581 and 3591. I...
8 comments posted 22yrs
posted by desert6traveler
8 comments posted 22yrs posted by desert6traveler

Layout table suggestions

Folks, After asking in the welding group about a 3 axis welding clamp and seeing Ernie's response that he used his layo...
11 comments posted 22yrs
posted by rchamSPOTberlain
11 comments posted 22yrs posted by rchamSPOTberlain

Schraeder valve OD tap

Hey all. I am wanting to build some custom made valve caps for my Harley. What is the OD thread size, and can I buy a bo...
7 comments posted 22yrs
posted by weldpeen
7 comments posted 22yrs posted by weldpeen

Saw abuse! (or: Do I need a plasma cutter?)

I have read that a hand held jig saw can be used to cut through 1/4 inch steel plate for fabrication purposes with reas...
14 comments posted 22yrs
posted by bryan
14 comments posted 22yrs posted by bryan

Anyone familiar with Gorton "collets"?

Anyone familiar with this type of quick change tool holders? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=2584828...
0 comments posted 22yrs
posted by gunner
0 comments posted 22yrs posted by gunner

Pewter sand casting advice?

Hi Folks, FYI, I have basic experience in casting small items with pewter in soapstone. As my next goal, I'd like to ma...
3 comments posted 22yrs
posted by ed_psycho
3 comments posted 22yrs posted by ed_psycho

Paper Punch Die Help?

A friend of mine has a business where he cuts 1" x 1.5" prints from a 11" x 14" xray sheet. Think of cutting those wall...
5 comments posted 22yrs
posted by gglines.NOSPAM
5 comments posted 22yrs posted by gglines.NOSPAM

what voltage is my mitutoyo digital readout

I have a 6" mitutoyo digital caliper that I bought in 1995.For quite a few years it gave me good service. 2 or 3 years...
4 comments posted 22yrs
posted by engineman1
4 comments posted 22yrs posted by engineman1