⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

OMAX 55100 Waterjet

eBay: http://easyurl.net/OMAX_55100
7 comments posted 19yrs
posted by Use-Author-Supplied-Address-He
7 comments posted 19yrs posted by Use-Author-Supplied-Address-He

Wire cutting in different Z-values

Hello, can anybody tell me if it's common to cut several conic shapes in different Z-values (e.g. Z1=5,Z2=2.5,Z5=0 for...
3 comments posted 19yrs
posted by palo.fulop
3 comments posted 19yrs posted by palo.fulop

What is it? CXC

http://puzzlephotos.blogspot.com/ Rob
10 comments posted 19yrs
posted by rhvp67
10 comments posted 19yrs posted by rhvp67

Nitrous Oxide and tubing cleanliness

I plan to run N2O into the air/fuel injector of my Aprilia SR50 Ditech scooter at 5 bar, around 75 PSI. Will it blow up...
10 comments posted 19yrs
posted by DGoncz
10 comments posted 19yrs posted by DGoncz

Foundry Auction et al

Thanks Mike, It has been an interesting adventure. I've never in 15 years, monitoring countless groups, seen a small fo...
0 comments posted 19yrs
posted by frank
0 comments posted 19yrs posted by frank

IronWood IW-1010 from Smithy

A few months ago I wrote that I was selling my tile saw if I got a Super Shop and modified it to cut stone. > ... > I a...
0 comments posted 19yrs
posted by DGoncz
0 comments posted 19yrs posted by DGoncz

HF MiniMag AA Light Repair

Pics and text in the Dropbox Pics show how to restore the on/off function on HF AA MiniMag light. http://www.harborfrei...
1 comments posted 19yrs
posted by junkjasonrnorth
1 comments posted 19yrs posted by junkjasonrnorth

A bench clamp for the Rockchucker

Warning: metal content. I made a clamp to secure a Rockchucker loading press to my workbench, enabling me to remove it...
63 comments posted 19yrs
posted by dforeman
63 comments posted 19yrs posted by dforeman

Miller Gold star 300ss

Not sure if this is the place to post this message but since it deals with welding I thought it might be the place to g...
4 comments posted 19yrs
posted by mcleod3ca55
4 comments posted 19yrs posted by mcleod3ca55

OT: Removing a snap line chalk mark from concrete

This is NOT a metal-related question but the people who post here seem to know a lot about all kinds of stuff. So here...
10 comments posted 19yrs
posted by grice
10 comments posted 19yrs posted by grice

Acetylene welding question

I sometimes to get an occasional pop while I am welding. BUT, what is it when I get rapid machine gun fire pops that co...
6 comments posted 19yrs
posted by ivan
6 comments posted 19yrs posted by ivan

double seal/quad rings vs Orings

I'm trying to repair the slave cylinder on my Clausing 6903 lathe. The lathe has a varidrive that the motor side is mov...
5 comments posted 19yrs
posted by clutch
5 comments posted 19yrs posted by clutch

Wood Preservatives

I want to put a preservative on the siding of my house. House is roughsawn white cedar clapboards, garage is roughsawn...
18 comments posted 19yrs
posted by jmartin957
18 comments posted 19yrs posted by jmartin957

saw blade w/ broke tooth still safe?

Hello everyone. I've using a mitre saw and non-ferrous cutting blade to cut some 1" 10 = series 80/20 for almost a year...
10 comments posted 19yrs
posted by _REMOVE_
10 comments posted 19yrs posted by _REMOVE_

flux-core with no gas nozzle?

I've got a microscopic amount of experience with MIG, and zero with fluxcore, so bear with me here: What happens if you...
29 comments posted 19yrs
posted by pfeiffer
29 comments posted 19yrs posted by pfeiffer