⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30761 Threads Posts
to

Worth reading in ⏣ General Metalworking

OT more than virus protection

To wet to work outside, too early for shop season. So, both office computers were just crawling. I put in new hard driv...
27 comments posted 16yrs
posted by karltownsend.NOT
27 comments posted 16yrs posted by karltownsend.NOT

Total War!

http://www.break.com/index/the-great-office-war.html
0 comments posted 16yrs
posted by gunner
0 comments posted 16yrs posted by gunner

ex-propane tank jack o'lantern

something i made. weak metalworking content. http://www.frontiernet.net/~wwixon/jacko'lanterns.jpg
5 comments posted 16yrs
posted by wwixon
5 comments posted 16yrs posted by wwixon

Ping: Dave

For some reason Thunderbird randomly refuses to send my replies to the group. Regarding the bolts, I'm pretty sure I go...
1 comments posted 16yrs
posted by fusion640
1 comments posted 16yrs posted by fusion640

Interesting proposal

HR 615 On Tuesday, the Senate health committee voted 12-11 in favor of a two-page amendment, courtesy of Republican Tom...
2 comments posted 16yrs
posted by cavelamb
2 comments posted 16yrs posted by cavelamb

Are there many treaters?

Last year I got about 50, and it was pretty even between boys and girls. By 7:15 tonight, 18 boys and 8 girls. Maybe eve...
12 comments posted 16yrs
posted by cayoung61**spamblock##
12 comments posted 16yrs posted by cayoung61**spamblock##

Turning common pipe

How can I turn 1.5" pipe and get a decent finish. Need to make a sleeve for a golf cart clutch and 1.5" pipe is close t...
9 comments posted 16yrs
posted by gmasterman
9 comments posted 16yrs posted by gmasterman

Interesting Bay Bridge Failure Article

Hi all, A friend sent this, thought the group would like to see it. In particular, note the rust accumulation in the 'E...
6 comments posted 16yrs
posted by spam
6 comments posted 16yrs posted by spam

15 hp 3P motor run on 10 HP Desco Panel?

Please forgive my ignorance but in the interest of possibly saving money, can I use the 15 HP motor I already have with...
4 comments posted 16yrs
posted by americansun
4 comments posted 16yrs posted by americansun

Anyone Speak Both English and French

...And want to quote a job in Quebec to a potential customer of mine as a distributor? I'll make you a distributor of s...
6 comments posted 16yrs
posted by autodrill
6 comments posted 16yrs posted by autodrill

Wells Iggy & me

I just scored a Wells mill. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250516918729&ssPageName=ADME:B:EOIBSA:US...
15 comments posted 16yrs
posted by karltownsend.NOT
15 comments posted 16yrs posted by karltownsend.NOT

Taper angles

I have a small woodworking router plane that has a vertical round rod carrying the blade on the lower end. The clamping...
8 comments posted 16yrs
posted by e_john_wilson.no.spam.
8 comments posted 16yrs posted by e_john_wilson.no.spam.

HSK63F to Female MT Adapters?

HSK63F to MT0, MT1, or MT2... Anyone know if such an animal exists off the shelf somewhere? Regards, Joe Agro, Jr. (800...
0 comments posted 16yrs
posted by autodrill
0 comments posted 16yrs posted by autodrill